Visit Our Website

 

This great article down below involving How to Install a Bathtub is quite attention-grabbing. Have a go and make your own ideas.

Mounting a tub isn't precisely brain surgery, but it does require strong plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old tub with a new one is also a moderately hard job. If the old bathtub is conveniently accessible, the task can relocate immediately; if you need to open a wall to get rid of the old bathtub and place the new tub, the task is a lot harder. In either case, the task is within a house handyman's skills, although you will need a helper to leave the old tub as well as embeded in the brand-new one. Ensure you have actually qualified on your own for the work and also are comfortable attempting it. Rather than working with a service provider to take over a halfway-completed job, it is better to think about using one before you start. Opportunities are you might need an expert plumber to make tube connections.
This post will certainly help you set up a new bath tub in your bathroom if you have actually currently bought a brand-new bathtub and also don't require to transform the setup of your previous water pipes.
Your devices and also material list should make up the following:

 

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Tape Measure


• Pipeline Caps


 

Planning for the Installment

To start with, the supporting frame provided with the bath needs to be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to make sure that if the tap includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps unit to avoid stress on the bath tub.
Fit the flexible faucet adapters to the bottom of both taps using 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to now prepare to be fitted in its final placement.

 

 

Removing Old Touches

If you need to replace old taps with new ones as a part of your setup, then the first thing you should do is disconnect the supply of water. After doing so, turn on the faucets to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be fairly problematic because of the limited accessibility that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will certainly come from the pipes. Once the supply pipelines have actually been eliminated, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old sealing substance.
Prior to proceeding to fit the new faucets, compare the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.

 

 

Mounting the Bath tub

Using the two wooden boards under its feet, position the bathtub in the called for position. The wooden boards are helpful in uniformly spreading the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 little points.
The following objective is to guarantee that the tub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the bathtub till the level reviews degree.
To set up faucets, fit all-time low of the furthest flexible faucet port to the suitable supply pipeline by making a compression join; after that do the exact same for the other faucet.
Switch on the supply of water and also examine all joints and new pipework for leaks as well as tighten them if necessary. Fill up the bathtub and also check the overflow electrical outlet and the normal outlet for leakages.
Finally, take care of the bath paneling as explained in the supplier's instruction manual. Tiling and also sealing around the bath tub ought to wait up until the tub has actually been utilized at the very least when as this will certainly settle it into its last placement.

 

 

Suitable New Taps

If the tails of the new faucets are plastic, then you will need a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the tap and also the other end provides a link to the current supply pipes.
If you need to fit a monobloc, after that you will need reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the mounting hole in the bath/basin making sure that the washers remain in area in between the tap and the sink. Safeguard the faucet in position with the manufacturer given backnut. Once the faucet is safely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with regular tap adapters. The former type must be linked to the faucet finishes first, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.

 

 

Tiling Around the Bath tub

In the area where the bathroom satisfies the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a stiff seal, causing the water to permeate the wall surface between the bathroom as well as the tiling, leading to problems with moisture and also feasible leaks to the ceiling below.
You can choose from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and also cartridges, and also are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always load the tub with water before sealing, to enable the motion experienced when the bathtub is in usage. The sealer can break relatively very early if you do not consider this activity prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise quickly readily available on the marketplace. It is a good idea to fit the ceramic tiles making use of waterproof or waterproof glue and also cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

We were made aware of that editorial on A Step-by-Step Guide to Installing a Bathtub from someone on our other web address. Enjoyed reading our piece of writing? Please share it. Let others locate it. I love reading our article about How to Install a Bathtub Yourself.

Schedule Now!